A Barrett company - serving Las Vegas, NV

CertainTeed Kitchen Remodeling in Las Vegas, NV

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

CertainTeed Kitchen Remodeling: The Las Vegas Owner’s Guide

We install CertainTeed kitchen remodeling materials – primarily CertainTeed’s gypsum board, joint compound, and moisture-resistant drywall systems that sit behind your cabinets, backsplash, and tile. A full kitchen remodel in Las Vegas runs $14,000 – $45,000 installed, and because we work around a fixed scope, we don’t promise same-day anything on a project this size. The discovery almost always happens mid-demolition or during an inspection: cabinets come out, and the drywall behind them is soft, crumbly, or stained from an old leak. Sometimes it’s a ceiling patch in the kitchen that starts sagging months after the roof was repaired. Either way, the CertainTeed board underneath has to be replaced correctly before anything new goes up, or the whole job inherits the same failure.

Call (866) 814-4155

Barrett & Sons Construction Las Vegas is an independent remodeling contractor. We are not affiliated with CertainTeed. We install CertainTeed products, and we’re honest about when they’re the right board for the room and when a different product is a better fit.

Key Takeaways

  • Las Vegas kitchens typically need moisture-resistant drywall near sinks and dishwashers, not standard board.
  • Behind-tile substrates and tile backer board in Las Vegas kitchens often fail from heat cycling and old slow leaks, not from impact.
  • CertainTeed’s board systems have specific fastener and joint-compound compatibility rules – mismatching them voids the fire and moisture ratings.
  • Permits get pulled and inspections get signed on every eligible job, so the board you paid for is the board the inspector sees.

Which CertainTeed Models This Applies To

CertainTeed’s drywall and gypsum family shows up in kitchens under a handful of product names, and matching the right one matters. The company’s moisture-resistant board (often sold under the M2Tech name) is the one we specify near the sink, dishwasher, and refrigerator line, where condensation and small leaks live. Standard 1/2-inch board is fine for dry kitchen walls in a Las Vegas home, but 5/8-inch Type X is the right call where a firewall separation exists between the kitchen and garage. For tile substrates, CertainTeed’s glass-mat backer board is the product line that replaces traditional cement board behind a backsplash or a tile accent wall – and this is where most owner-supplied material goes wrong.

Here’s the identification step most people skip. Pull the label off the edge of any existing board before you buy replacement material. CertainTeed stamps the product name, thickness (1/2-inch, 5/8-inch), and whether the board is moisture-resistant or fire-rated directly on the edge tape. If the label is gone, measure the thickness and note whether the paper face is green, blue, or standard gray. Green or blue-faced board is moisture-resistant and should get moisture-resistant replacement – never standard board in its place. Board thickness also has to match, or the tile and cabinet reveal will be off by a quarter inch across the whole wall.

On the OEM-versus-aftermarket decision: CertainTeed’s own fasteners, joint compound, and tape are formulated to work as a system. Mixing a generic joint compound with CertainTeed board isn’t automatically a failure, but it can void the manufacturer’s stated fire rating for a Type X assembly. Where the assembly carries a fire rating, we use the matching system. Where it doesn’t, a quality aftermarket equivalent is fine and we’ll tell you so. We don’t stock parts on a truck and we don’t carry CertainTeed material in inventory – we source it per job so you’re not paying for board that’s been sitting on a rack. We install KraftMaid, Cambria, and Silestone for the cabinetry and counter side of the same kitchen.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your CertainTeed Kitchen Remodeling Is Failing

Behind-the-wall problems in a Las Vegas kitchen show up in a few predictable ways. Here’s what the symptoms actually mean.

  • Soft or crumbling board behind the cabinets. A slow leak under the sink or a failed dishwasher seal has been wicking into the gypsum for years. CertainTeed board – even the moisture-resistant line – will eventually break down if the water source keeps feeding it. The fix is finding the leak first, then replacing the board.
  • Popped screws or bubbling paint near the backsplash. Thermal movement is the usual culprit. Las Vegas summers swing wall assemblies hard, and when board was fastened too tight against framing, the movement telegraphs through the finish. If you see a row of popped screw heads, that’s the board telling you the framing behind it may also have shifted.
  • Stained or sagging ceiling patch in the kitchen. Often the residue of an old roof leak that was painted over instead of repaired. The CertainTeed board absorbs and holds the moisture, and once saturated it has to come out. We see this regularly in kitchens below a flat or low-slope section of roof.
  • Cracks along a corner or over a door frame. Settlement or a joint that wasn’t taped and bedded correctly. It’s cosmetic until it isn’t – if the crack is wider than a credit card edge and runs diagonally, the underlying board may have separated from the framing.
  • Tile backing that flexes when you press on it. A glass-mat backer or cement board that wasn’t set with the correct thin-set or wasn’t properly fastened will flex. Flex under tile means cracked tile within a year or two in Southern Nevada’s heat.

For any of these, we recommend a trained crew take a look. Board replacement in a kitchen means moving cabinets or counters, and pulling the wrong board can crack surrounding tile. It’s not a job to start on a weekend without a plan.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Board replacement in a Las Vegas kitchen is rarely a standalone line item, so the honest number is the whole job. A kitchen remodel runs $14,000 – $45,000, and behind-wall board work typically gets rolled into that scope. Standalone pricing for related trade items:

  • Cabinet installation: $4,000 – $13,000
  • Countertop installation: $2,000 – $6,500
  • Backsplash installation: $800 – $2,500
  • Kitchen island installation: $3,000 – $10,000
  • Small kitchen remodel: $9,000 – $20,000

What drives the range: how much board comes out, whether the leak source needs repair first, whether tile has to come off the wall to reach the board, and whether framing has to be replaced. Every scope, every allowance, every price change arrives as a written change order before work happens. Install work is backed by our written 90-Day Done Right Promise on every job.

DIY or Call Us?

Some things you can safely check yourself. Pull the edge label on any exposed board and record the product name and thickness. Look under the sink with a flashlight for staining or soft spots. Press gently on the backsplash tile to check for flex. Note which cabinet it’s next to. That’s the information a crew needs to price the job accurately.

Where DIY goes wrong: cutting out and replacing board yourself in a Las Vegas kitchen usually means disturbing tile, disconnecting a water line, or leaving a joint that doesn’t hold the fire-rating the assembly was built with. If a fire-rated wall is involved, an unpermitted patch can fail inspection and cost more to correct than the original work. We pull permits and pass inspections on every eligible job, and the inspector is the best protection your house has.

Our crew members have up to 28 years of experience on this exact work. Call (866) 814-4155 for a free estimate – we’ll look at what you’ve got before you buy a single sheet.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 814-4155
Local Service Coverage

Request a Free Estimate in Las Vegas

Tell us what you need - Barrett & Sons Construction Las Vegas responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch