Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Las Vegas Owner’s Guide
Kitchen remodeling with Barrette cabinetry in Las Vegas typically runs $14,000 – $45,000 installed, depending on layout, door style, and whether you’re keeping the existing footprint or reworking plumbing and electrical. A cabinet-only swap usually lands in the $4,000 – $13,000 range. We’re an independent installer of Barrette-compatible kitchens, working alongside KraftMaid, Cambria, and Silestone when a project calls for them.
Most Las Vegas homeowners call us before they’ve named a single door style. What they describe is a symptom, not a product: a cabinet door that no longer sits flush, a drawer that needs a shoulder to close, a hinge that pops off its plate, or a particleboard shelf in a base cabinet that has gone soft under the dishes. In Vegas, that last one is common. Barrette boxes that sit on a garage-adjacent wall or under a south-facing window take a hard summer. The adhesive holding a laminate door frame together softens, the door gaps, and the whole face frame starts to look like it’s been through something. These are the calls we take most.
Which Barrette Models This Applies To
Barrette cabinets aren’t a single product. The brand has covered stock, semi-custom, and builder-grade lines over the years, and the parts inside the same brand can be different door to door, drawer to drawer, and year to year. The good news is that the interface pieces (hinges, drawer glides, shelf clips, and the standard interior hardware) are largely interchangeable across the brand’s mid-tier lines. The trouble is at the edges: a euro hinge that works on a thermofoil door may not seat right on a solid wood door of the same dimensions, because the door thickness and the bore pattern differ by a millimeter or two.
Here’s how to identify what you actually have. Pull open a base cabinet and look for a label on the inside of the left side panel, often near the top or behind the top drawer. You’re looking for a series name or a model code. If the label is gone (they fade and peel in Vegas heat), measure the door thickness (Barrette mid-tier doors are typically 3/4 inch, but thermofoil doors often run slightly thicker), and measure hinge bore spacing from the door edge. Those two numbers tell us which replacement part kit will actually fit. On a semi-custom line, the interior finish also tells the story: full-depth adjustable shelving with a different interior color from the box means you’re in a different tier than builder-grade.
OEM vs. aftermarket is the practical decision. On a shelf clip or a standard hinge, a quality aftermarket equivalent (Blum, Hettich, or a Barrette OEM part) will outlast the original by years. On a branded laminate door or a thermofoil face, going OEM is worth it because the face profile and edge banding won’t match a generic replacement. We don’t stock parts and we don’t carry them on a truck. We source, measure, and install. Our crew has up to 28 years of experience and we’re not affiliated with Barrette; we’re an independent Las Vegas installer who knows the brand’s parts.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Kitchen Remodeling Is Failing
If you’re calling us, one of these is likely the reason:
- The drawer closes with a clunk but doesn’t stay closed. The soft-close glide has lost its damping or the rail has worn at the attachment point. In a Las Vegas summer, the cabinet box expands and contracts, and the glide can’t hold its alignment. This gets worse in the kitchen cabinet that faces the afternoon sun.
- A hinge screws into wood but pulls out on a second swing. This is stripped screw holes, often from the door swinging on a hinge that’s been under load for years. On particleboard boxes, the pilot hole elongates and eventually the hinge won’t hold.
- The cabinet door is sagging and won’t square up. The hinge plate has bent or the door has swollen at the hinge bore from humidity. Barrette doors with thermofoil faces are sensitive to this when the kitchen has a wall shared with a hot garage.
- A base cabinet shelf feels soft or has started to bow. Particleboard or MDF shelving in a lower cabinet, especially a corner or one under a sink, absorbs moisture and loses integrity over time. Once it bows, it stays bowed. Replacement is the fix, not a reinforcement.
- The cabinet box has separated at a joint or a corner. This is a structural failure, not a hardware failure. The joint has opened from movement, and the face frame is no longer holding the box square. This is the one where a full re-face or partial replacement is usually cheaper than trying to repair.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a single cabinet, cabinet door, or drawer box replacement in Las Vegas, the range is $300 – $900 installed, including sourcing and a written scope. A hardware-only job (hinges, glides, shelf clips) is $150 – $500, depending on how many pieces and what’s involved in getting the old hardware out. If the failure has gone structural and you’re into a partial kitchen rework, you’re at the cabinet installation range: $4,000 – $13,000. Full kitchen remodel, all-in: $14,000 – $45,000.
What drives the range is simple: how many pieces, whether the part is OEM or an aftermarket equivalent, and whether the failure is structural or just hardware. Filtering by cost, the line item that hurts most is a door replacement on a semi-custom Barrette line, because the door profile has to match the existing face, not just the dimensions. We write every scope and every price change in writing before work starts. If we find something behind a cabinet that changes the scope, you get a written change order before a screw is turned. The work is backed by the 90-Day Done Right Promise: if something we did isn’t right, we come back and make it right.
DIY or Call Us?
You can safely check the obvious: open the cabinet, look for a label, measure the door thickness and the hinge bore spacing, and photograph the failed hinge or glide. That’s information we need, and it saves a visit. You can also tighten a hinge screw into an existing hole with a longer screw, or slide a plastic shelf clip back into place, and there’s no risk in that.
Where DIY goes wrong on a Barrette kitchen is at the structural repair or a full door-and-drawer swap. A cabinet box that’s out of square is not a job for a drill and a YouTube video. It’s a job for someone who can pull the cabinet, level it, and re-set it without cracking the face frame. And a stripped hinge on a particleboard box is a fix that lasts two weeks if you just go up a screw size. We’d rather you call us and let a crew member with up to 28 years of experience look at it than have you chase a repair three times. Call (866) 814-4155 to schedule your free estimate. We also offer a Free Second Opinion on any written estimate, and a $40 Off Any Repair Over $200 when it’s the right fit.
FAQs
Hinges and drawer glides on Barrette cabinets typically work well for 10 – 15 years before soft-close damping wears out or a hinge starts pulling. The cabinet box itself usually lasts decades. What shortens lifespan in Las Vegas is the summer heat and the dry-then-humid swing inside a kitchen that shares a wall with a garage. Interiors that stay cooler tend to hold longer. When a part fails early, it’s usually a hardware piece, not the box.
Sometimes. A hinge that’s stripped can often be repaired with a longer screw or a threaded insert, and a glides that just needs a clip replaced is a cheap fix. But a bowing shelf in a base cabinet, or a face frame that’s separated at a corner, doesn’t repair well. In those cases a replacement is the honest answer. Call (866) 814-4155 and we’ll tell you which one you’re looking at.
A hardware-only replacement (hinges, glides, clips on a few cabinets) is usually done in a couple of hours, same visit. A door replacement or a single cabinet box swap is typically a half-day to a full day for the crew. A partial kitchen rework is a multi-day job. We’ll tell you the realistic window in writing before we start.
We measure first, then source. You don’t need to know the model name, and you don’t need a part number. Give us the door thickness, hinge bore spacing, and a photo of the failed piece, and we’ll identify the right Barrette-compatible part or an aftermarket equivalent to match. We don’t carry parts on a truck, and we don’t stock them. We source for the specific job, so the part you get is the part that fits.
If your Barrette kitchen is telling you something is failing, the first move is a free estimate. Call (866) 814-4155 to schedule yours. We’ll look at what you’ve got, tell you whether it’s a repair or a replacement, and put the scope in writing before anything starts.
Written by the team at Barrett & Sons Construction Las Vegas, serving Las Vegas and nearby areas.