Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Las Vegas Owner’s Guide
Schluter doesn’t make driveways or pavers – it makes the profile, edge, trench-drain, and uncoupling systems that make a hardscape last, and when one of those components fails, a paver driveway in Las Vegas can shift, pond water, or drop at the apron within a season of our heat. Installed repair and replacement work on the components we handle runs from roughly $250 for a drainage or edge fix up to the $7,000-$18,000 range for a full Schluter-compatible paver driveway installation, and we don’t blanket-promise same-day service on planned hardscape work – we quote it honestly and schedule it right. Owners usually call us after they notice a paver edge lifting at the driveway apron, water sitting in a low spot where a Schluter drainage profile used to move it, or a paver band that wandered 3/8 of an inch after one summer of 115°F days. The system didn’t fail all at once – the profile under or beside the pavers did.
Which Schluter Models This Applies To
Schluter’s hardscape lines that matter to a Las Vegas driveway are narrower than most people expect. You’re likely dealing with one of these:
- PAVEPRO – the load-bearing profile for transitions between pavers and adjacent surfaces (driveway to garage apron, driveway to turf, driveway to concrete walk). Las Vegas heat cycling is hard on the anchoring legs.
- DILEX-PAV – the expansion-joint profile for paver fields that move with temperature. In the Mojave, this is doing more work than in any other climate.
- TROBA-MR / TROBA-PLUS – drainage/uncoupling mats under the paver bed, used where water is funneled away from the slab. On our caliche-heavy soil, drainage is the whole ballgame.
- SHOWERPROFILE and pavers – if you’ve seen “Schluter” pavers and it’s really a hardscape edge used at a floor transition, it’s usually PAVEPRO, not a paver.
How to identify the right part
Look at the visible trim at your driveway edge, apron, or drain line. Schluter profiles are extruded metal or rigid PVC with a U- or C-channel and a perforated anchoring leg – they’ll have either their name stamped lightly on the visible face or a small print ID tag tucked into the channel end you can work loose with a putty knife. Measure the channel width with a caliper if you can; the profile must match your paver thickness within about 1mm, not “close enough.” The biggest compatibility gotcha most homeowners miss: PAVEPRO sizes are keyed to paver thickness (typically 3/4″ / 20mm for standard brick pavers, up to 1-1/4″ for larger unit pavers), and the wrong thickness means the anchoring leg doesn’t bite – it’ll pull out the first hot week. If you’re unsure, photograph the profile end and any stamped markings; we can match it.
OEM vs aftermarket – the honest answer for Schluter
Schluter’s profiles are precision extrusions with genuine engineering behind them; the aftermarket far less so. We spec Schluter-compatible components on the work we install, and we’ll tell you plainly when a quality equivalent actually saves real money (it’s rare for PAVEPRO and DILEX-PAV, more common for generic drainage mats) and when it’s a bad bet. We do not carry or stock parts and we don’t claim to – we’ll source what your job needs and put the price on your written estimate.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
- Paver edge lifting or tilting at the driveway apron. Usually the anchoring leg of a PAVEPRO profile has cracked or pulled loose under thermal expansion against a rigid concrete edge. The paver looks like it “heaved” – really the profile stopped holding it.
- Water sitting in the same low spot after rain or irrigation. A TROBA mat or drainage profile has either clogged with our wind-blown dust/sand or the bedding layer has settled where it exits. Standing water in a Las Vegas cul-de-sac is a grading-and-drainage failure, not just a puddle.
- Paver field shifting in a repeating pattern over a 30-40 foot span. This is a DILEX-PAV expansion joint issue – the joint has been overloaded by our daily 50+ degree temperature swings and either the profile debonded or the pavers lost their joint width.
- Visible crack in the profile extrusion. Aluminum and PVC both get brittle after years of UV exposure and 100°F-plus surface temperatures. A cracked profile is a failed profile – it will not hold the paver edge it was installed for.
- Pavers breaking at a specific line across the driveway. The profile has become a hard point where load concentrates. Each season you wait, more pavers break.
In our experience on Henderson and Spring Valley driveways, the profile issue usually shows up 8-12 years in, not because Schluter made a bad part – because the anchoring system under our sun and soil conditions is doing more work than in cooler climates, and a 1/8″ installation error becomes a failure.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Schluter-specific repair and replacement on a Las Vegas driveway prices out roughly like this. These are installed ranges – parts plus labor – because that’s how you’ll actually see the bill:
- Schluter profile or drainage component repair or replacement (localized): $250-$700, including the profile, bedding adjustment, and disturbed paver reset.
- Full paver driveway installation with Schluter-compatible edge and drainage detailing: $7,000-$18,000, depending on square footage, paver spec, drainage complexity, and whether any slab or apex work is needed.
- Paver patio installation: $3,500-$11,000 for the same reason – the profile and drainage detailing is the labor-intensive part.
- Driveway sealing (post-install or after repair): $250-$700.
What drives the range: how much paver field has to come up to reach the profile, whether a concrete apron has to be cut back, and whether the existing drainage mat can be reused. We don’t do “guess the price” – you get a written line-item estimate with the profile brand and spec named and a written change order if scope changes on the job. The completed work is backed by our 90-Day Done Right Promise, written on the contract, and if a profile we installed fails in that window we come back.
DIY or Call Us?
Some of this is safe to check yourself. Walk the driveway edge and apron, look for lifting pavers, note where water ponds, and photograph any visible profile markings. What you shouldn’t do yourself is pull pavers to inspect the anchoring leg on a load-bearing edge – a paver field without a working profile can shift and cause a fall, and getting the anchoring leg reseated correctly requires matching paver thickness to the profile within a millimeter, resetting the bedding at the correct slope, and reinstalling the profile so it bites the edge and doesn’t just sit on top. That’s the part that goes wrong silently and shows up next summer. Call us at (866) 814-4155 for a no-charge look – Barrett & Sons Construction Las Vegas is an independent contractor; we’re not affiliated with Schluter, but we know the profiles and we’ll tell you if the plan you have in mind will hold up.
FAQs
Realistically 8-12 years on a driveway that gets direct Mojave sun and regular irrigation exposure, which is shorter than the 20-year expectation you see in cooler climates. The two things that shorten it fastest are missing anchoring-leg seating at install and drainage mat clogging with our wind-blown sand. Call (866) 814-4155 for an exact quote – estimates are free.
Often, yes. A single lifted apron paver with an intact profile can be reset; a debonded DILEX-PAV joint can sometimes be re-bonded if the profile body isn’t cracked. If the profile itself is cracked or the anchoring leg has failed along a length of driveway, replacement is the honest call. We’ll tell you which is which, in writing.
A localized profile repair is typically a half-to-full day. A full paver driveway install with Schluter-compatible edge and drainage detailing is usually 2-4 days for a residential driveway, weather and scope depending. We won’t tell you it’s a one-day job and then leave you with a tarp for a week.
We source by part number, name, and thickness – not by “just get me one of those trim things.” We’ll confirm the exact Schluter profile or drainage component on your written estimate before we order it, so you’re not paying Labor Day pricing on a holiday-week special order. If we can’t match your existing part, we’ll tell you and quote a quality equivalent with the difference noted.
Yes, on every eligible job. Pavers and driveways in Las Vegas are typically permitted through Clark County or the City of Las Vegas depending on where you are; we pull the permit and the inspection gets signed. The permit inspector works for you, not for us – that’s why we like him.
Call (866) 814-4155 to schedule your free estimate. A live person answers the phone 24 hours a day, 7 days a week. We stand behind every completed job with the written 90-Day Done Right Promise – if it’s not done right, Tom comes back. And remember the standing offers: $40 Off Any Repair Over $200, a Free Second Opinion on Any Written Estimate, No Trip Charge Inside the County, and a permanent 10% Senior & Veteran discount. We install Schluter-compatible work alongside other premium brands you’ve probably already got in the house – KraftMaid, Cambria, and Silestone – so if the paver project is part of a bigger backyard plan, we can quote the whole thing in one written scope. Ask anyone on your street, or call us and we’ll walk out and look with you.
Written by the team at Barrett & Sons Construction Las Vegas, serving Las Vegas and nearby areas.