A Barrett company - serving Las Vegas, NV

Schluter Home Additions & ADU in Las Vegas, NV

Home additions & ADUHome additions & ADU
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Home Additions & ADU: The Las Vegas Owner’s Guide

A Schluter system on a home addition or ADU in Las Vegas typically runs $45,000 – $130,000 depending on square footage and finish level, and we usually have a crew member out to look at yours within the week. What brings most owners to this page is a failure they didn’t see coming: a shower floor that starts weeping near the drain, a heated floor that quits in one room, or grout that lets go at a wall-to-floor joint the first summer after install.

Call (866) 814-4155

Schluter makes a specific promise with each of its product lines, and when one of them fails, the fix is not a tube of caulk. It’s understanding which product you have, what failed inside it, and what goes back in its place. That’s what this page covers.

  • $45,000 – $130,000 is the broad install range for a Schluter-systemed addition or ADU.
  • Schluter failures are almost always a system mismatch or water intrusion, not a defective product.
  • Las Vegas heat cycling is hard on thinset and membrane bonds.
  • We are an independent contractor and are not affiliated with Schluter.

Which Schluter Models This Applies To

Schluter’s addition-relevant product families show up in three places on a project this size. Schluter-DITRA is the uncoupling membrane under tile floors, sold in rolls of 3’3″ and 1-meter widths and in sheet formats. DITRA-HEAT is the version with heating cable clips molded into the mat. Schluter-KERDI is the waterproofing membrane for shower walls and floors, most often in 5-meter and 10-meter roll lengths and 125-mil thickness. Schluter-SHOWERPROFILE and KERDI-LINE linear drains sit inside those systems, and those drains are where a lot of water intrusion calls start.

You’ll find the product name stamped on the membrane fleece or printed on the roll’s edge band. Grab a photo of that stamp, plus a tape measure reading across the roll width. Older stock and current stock of DITRA can look identical on the surface, and the printed model code on the edge is the only reliable way to match the right replacement membrane or cable clip set.

For accessories – drain flanges, profile trims, cable thermostats – the OEM-versus-aftermarket call matters more than most owners expect. Generic uncoupling mats share the dimple geometry but not the shear bond testing behind DITRA, and a mismatched drain flange can fail the rough-in inspection. On a job this expensive, matching the correct Schluter component is the cheapest insurance you’ll buy. We also install KraftMaid, Cambria, and Silestone in the finished spaces.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Home Additions & ADU Is Failing

  • Grout cracking in straight lines across a floor. That pattern usually means the membrane underneath has separated from the slab or the thinset bond broke, so movement transfers straight up into the tile.
  • Soft spot or hollow tap near a shower drain. Water is getting under the KERDI rather than shedding over it, often where the drain flange meets the membrane. Left alone, this rots the subfloor from the top down.
  • DITRA-HEAT that heats in half the room. A single cable run has usually failed at a clip or a field splice, and the thermostat reads fine while a whole zone stays cold.
  • Musty smell in an ADU bathroom that never dries out. That’s trapped moisture in the wall assembly, not a bad exhaust fan, and it points back to a KERDI seam that was never properly banded.
  • Lippage or tile popping loose at the perimeter of a slab. Thermal movement at the slab edge is the culprit here, and it shows up fast in Las Vegas where a south-facing slab and an unshaded patio can swing thirty degrees between morning and afternoon.

One thing worth saying plainly: the interior waterproofing and membrane work on a Schluter addition isn’t a friendly DIY project. It’s buried under tile, it has to be right the first time, and getting a KERDI seam wrong means tearing out finished work later. We’d rather tell you that up front than sell you a fix that fails again.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Replacing failing Schluter work on a Las Vegas addition runs from a few hundred dollars for a small area repair up to the full $45,000 – $130,000 range if the failure extended far enough that the room has to come apart and go back together. Here’s how that breaks down.

  • Localized DITRA-HEAT cable repair: $450 – $1,800, depending on how much tile comes up to reach the failed run.
  • Shower floor KERDI rebuild (drain flange reset, membrane, tile): $2,500 – $6,500.
  • Full ADU bathroom waterproofing redo: included in the ADU line below when it’s part of a larger scope.
  • Home Addition with Schluter system, full scope: $45,000 – $130,000.
  • ADU Construction with Schluter system, full scope: $90,000 – $220,000.
  • Garage Conversion with Schluter system: $30,000 – $80,000.

What moves the number most is how much finished tile has to be removed to reach the failed membrane or cable. Our technicians have up to 28 years of experience reading these failures before demolition, so we can tell you early whether it’s a localized patch or a deeper rebuild. Every price change during the job arrives as a written change order before the work happens. Every eligible job gets permits pulled and inspections signed, and the whole repair is covered by our 90-Day Done Right Promise.

DIY or Call Us?

Some things you can safely do yourself. Photograph the product stamp on the membrane. Measure the roll width. Test the DITRA-HEAT thermostat and check the breaker. Poke around and figure out where the water is actually coming from. If it’s a shower leak or a heating cable that quit, call us at (866) 814-4155 – that’s the point where DIY gets expensive fast, because re-tiling over a bad membrane just hides the problem for a season.

The repair itself isn’t the place to save a few hundred dollars. Schluter systems depend on specific thinset, specific banding, and specific cure times, and a seam that looks fine on a Saturday can leak by the next summer in Las Vegas heat. Call (866) 814-4155 for a free estimate and we’ll tell you straight whether it’s a patch job or a rebuild.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 814-4155
Local Service Coverage

Request a Free Estimate in Las Vegas

Tell us what you need - Barrett & Sons Construction Las Vegas responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch