Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sterling Kitchen Remodeling: The Las Vegas Owner’s Guide
We install Sterling-compatible kitchen remodeling in Las Vegas, and a full kitchen typically runs $14,000 – $45,000 for the whole job when you’re refreshing cabinetry, counters, and a backsplash together. Here’s the short answer on parts: Sterling has been a cabinet and kitchen fixture line carried through dealers and box stores, so what actually fails is almost never “the Sterling” itself. It’s the hinge, the drawer glide, the shelf clip, the door face, or the counter seam that takes the beating.
Most Las Vegas owners find us in one of two ways. Either a cabinet door has started to sag and won’t sit flush anymore, or a drawer sticks so hard a grandkid can’t open it, and they go looking for a “Sterling part.” The other way is a 2003-era Sterling kitchen in Summerlin or Green Valley where the doors have gone soft at the bottom from years of dry desert air and the counters are lifting along a seam. Both roads lead to the same place: matching the right component to the right cabinet box, and doing it before a small fix turns into a face-frame repair.
Key Takeaways
- Most Sterling kitchen “failures” are hinges, glides, and door faces, not the cabinet box itself.
- We verify parts by measuring the cabinet opening and hinge boring pattern, not by guessing from a model number.
- Full kitchen remodels in Las Vegas run $14,000 – $45,000; single parts and repairs are quoted line-item.
- We’re an independent contractor, not affiliated with Sterling, and we tell you that up front.
Which Sterling Models This Applies To
Sterling cabinetry has been sold across a handful of lines through dealer showrooms and home centers, and the model line matters far less than three measurements on the actual cabinet in your kitchen. First, the cabinet box depth: standard base cabinets are 24 inches deep and 34½ inches tall, but Sterling made some 12-inch-deep wall units and a few 21-inch base depths for tighter galley kitchens, and those take different hinges and glides than the standard stamp.
Second, the hinge boring pattern. Euro-style concealed hinges in Sterling cabinets almost always use a 35mm cup bored 3mm from the door edge, but the screw-hole spread and the overlay offset vary between the older Sterling lines and the more recent ones. Measure the overlay (how much the door laps the cabinet face) before you order anything. Third, the drawer glide style. Early Sterling drawers ran on a side-mount roller glide that’s often undersized by today’s standards; later lines moved to an under-mount that tracks a full-extension pull.
On the OEM-versus-aftermarket question: for Sterling cabinet hardware, a quality aftermarket hinge or glide from a name brand like Blum or Grass will outlast the original OEM piece and usually fits the same boring pattern. The catch is the boring pattern itself. If your Sterling doors are the older 35mm pattern with the narrow screw spread, an off-the-shelf hinge that “fits a 35mm hole” may still walk out of position. We measure and confirm the spread before we order, and we tell you plainly when an OEM match is the safer route and when an aftermarket piece is the better buy. Our crew members have up to 28 years of experience matching hardware to older cabinet boxes, and that’s usually what saves a job from a return-and-reorder cycle.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Sterling Kitchen Remodeling Is Failing
- A cabinet door that won’t close flush. That’s almost always a worn hinge cup or a stripped screw hole in the door, not the door itself. If the door sags at the bottom corner, the hinge is the first suspect.
- A drawer that sticks halfway out. Side-mount roller glides collect dust and lose their track tension, and in Las Vegas the dry air hardens the original lubricant until the glide drags. Under-mount glides fail less often but pop loose at the rear clip.
- Doors that have gone soft or delaminated at the bottom edge. Steam from the dishwasher and years of low desert humidity swing combine to swell the door core. Once the edge lifts, refinishing won’t hold and the door needs replacing.
- A counter seam that’s lifting or showing a hairline crack. Slab movement under the heat, or a caulk joint that dried out, lets water get under the seam. Left alone, that’s a countertop replacement rather than a reseal.
- A backsplash tile that’s popped off the wall. Thinset that didn’t bond to the drywall behind it lets a tile go loose. It’s a small fix if you catch it before the adjacent tiles follow.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what things actually cost in the Las Vegas market, and we quote every line so you can see where the money goes:
| Item | Installed Price Range |
|---|---|
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
The range on a full remodel comes down to cabinet line, counter material, and whether the layout changes. A door-and-glide swap on existing Sterling boxes sits at the low end because you’re not tearing out the cabinet. Premium counters like Cambria or Silestone push it higher. Parts and labor are quoted separately and in writing, and every price change is a written change order issued before we touch the job. That’s the whole point of the 90-Day Done Right Promise: if a hinge we installed isn’t right, one call brings us back.
DIY or Call Us?
You can absolutely check this yourself before you call anyone. Open and close every cabinet door and watch for the sag. Pull a drawer out and look at the glide – side-mount roller or under-mount? Measure the cabinet opening and the door overlay. Write down the numbers, and you’ll know more about your Sterling kitchen in ten minutes than most people ever do.
Where DIY goes wrong: swapping a hinge on the wrong boring pattern, forcing a glide clip into an oversized hole, or reseating a counter seam that’s already failed underneath. None of that is dangerous the way a gas line or an electrical panel is – which is why we’ll never tell you to leave it to a pro out of fear. But it is easy to make a small fix into a bigger repair, and a stripped hinge screw hole in a Sterling door is a real pain to close back up once it’s gone soft.
We carry premium brands across the trades we touch – KraftMaid, Cambria, Silestone, and others you can look up rather than take our word for. If you’d rather have it done right the first time, call (866) 814-4155 and we’ll take a look.
FAQs
Quality hinges and glides should give you 15 to 20 years of daily use, but in Las Vegas’s dry climate the original lubricant dries out faster and you’ll often see the first glide failure closer to year 10. The cabinet box itself will outlast the hardware by a wide margin. If yours is past that window, call (866) 814-4155 for a free look.
Sometimes. A loose hinge screw can be filled and re-driven, and a side-mount glide can occasionally be re-tensioned, but once the cup or the clip is worn, replacement is the honest answer. We’ll tell you which one you’re looking at. Call (866) 814-4155 for an estimate.
A single hinge or glide swap is often an hour or two; a full cabinet door replacement on a Sterling kitchen typically takes a day. Counters and backsplash are the longer jobs at two to four days. Your written estimate will list the timelines.
We measure the boring pattern and overlay on your actual cabinet, then confirm the part against that spec before ordering, from a dealer or a name-brand aftermarket supplier. We don’t guess from a model number, and we don’t carry parts on a truck. Call (866) 814-4155 and we’ll start with a measurement.
If you’re ready to stop guessing and get a written, line-item quote, call Barrett & Sons Construction Las Vegas at (866) 814-4155. We’ll measure your Sterling kitchen, quote the right part or the full remodel, and put every number on paper before any work starts.
Written by the team at Barrett & Sons Construction Las Vegas, serving Las Vegas and nearby areas.